EN60350-2 Figure Z1 Standardized Cookware / Stainless Steel Standard Cooking Vessels for Cookware

日期：2026-04-18 02:37

瀏覽次數(shù)：274

摘要：EN60350-2 Figure Z1 Standardized Cookware / Stainless Steel Standard Cooking Vessels for Cookware

EN60350-2 Figure Z1 Standardized Cookware / Stainless Steel Standard Cooking Vessels for Cookware

1. Introduction
The vessels are designed according to EN60350-2:2013 figure Z1, the side wall of the vessel is made of 1.4301 stainless steel with thickness 1mm±0.05mm, the bottom of the vessel is made of 1.4016 stainless steel with thickness 6mm±0.05mm, the cookware is cylindrical withour handle or protrusions. And the lid is made of aluminum, and thickness is 2mm±0.05mm, each hole circle of the lid has a diameter of 16mm±0.1mm, the holes shall be evenly distributed on the hole circle. The lid is flat and can accommodate a temperature sensor in the center.

2. Parameter

Sizes of Standardised Cookware and Water Amounts

Diameter of the cookware bottom (outstide)

mm

Diameter of the lid

mm

Lid holde circle diameter

mm
Number of holes on the circle
Total cookware height (outside)

mm

Flatness of cookware bottom

mm

Water load

g

Cooking zone size category

mm
Standardised cookware categories

120±0.5 130±1 80±1 7 125±0.5
≥0

<0.075
650
≥100

<130
A

150±0.5 165±1 110±1 11 125±0.5
≥0

<0.075
1030
≥130

<160

180±0.5 200±1 140±1 16 125±0.5
≥0

<0.075
1500
≥160

<190
B

210±0.5 230±1 170±1 22 125±0.5
≥0

<0.1
2050
≥190

<220
C

240±0.5 265±1 200±1 29 125±0.5
≥0

<0.1
2700
≥220

<250

270±0.5 300±1 230/210^a±1 18/18^a 125±0.5
≥0

<0.15
3420
≥250

<280
D

300±0.5 330±1 260/210^a±1 23/22^a 125±0.5
≥0

<0.15
4240
≥280

<310

330±0.5 365±1 290/270^a±1 27/27^a 125±0.5
≥0

<0.15
5140
≥310

≤330

Number of holes are arranged on two hole circles

Next: Impact Test Vessel with Flat Aluminum Base as per IEC60335-2-6 clause 21.102
Previous: IEC60529 IP Rating Testing IPX3 / IPX4 Water Spray Nozzle with Brass Sprinkler Head and Aluminum Baf

粵公網(wǎng)安備 44030602001691號

Diameter of the cookware bottom (outstide) mm	Diameter of the lid mm	Lid holde circle diameter mm	Number of holes on the circle	Total cookware height (outside) mm	Flatness of cookware bottom mm	Water load g	Cooking zone size category mm	Standardised cookware categories
120±0.5	130±1	80±1	7	125±0.5	≥0 <0.075	650	≥100 <130	A
150±0.5	165±1	110±1	11	125±0.5	≥0 <0.075	1030	≥130 <160	A
180±0.5	200±1	140±1	16	125±0.5	≥0 <0.075	1500	≥160 <190	B
210±0.5	230±1	170±1	22	125±0.5	≥0 <0.1	2050	≥190 <220	C
240±0.5	265±1	200±1	29	125±0.5	≥0 <0.1	2700	≥220 <250	C
270±0.5	300±1	230/210^a±1	18/18^a	125±0.5	≥0 <0.15	3420	≥250 <280	D
300±0.5	330±1	260/210^a±1	23/22^a	125±0.5	≥0 <0.15	4240	≥280 <310
330±0.5	365±1	290/270^a±1	27/27^a	125±0.5	≥0 <0.15	5140	≥310 ≤330
Number of holes are arranged on two hole circles